1,75mm CarbonFil Karbonarmert PET-G 500g

1,75mm CarbonFil Karbonarmert PET-G 500g

399,00 NOK

(inkl. mva.)

Ingen produktomtale

Produsent

FormFutura

Materiale

PET-G + 20% Karbonfiber

Toleranse

0,05mm

Oppvarmet byggeplate

0-60°C

Printetemperatur

230°C - 265°C

Spolestørrelse 200mm X 55mm
Spole Senterdiameter53mm
Vekt tom spole270g

 

 

Modell/varenr.: 171-0-FCAR
Lagerstatus: Bestillingsvare med kort levering
stk.
Our CarbonFil filament is based upon the unique PETG blend of our HDglass compound and is reinforced with 20% ultra-light and relatively long stringer carbon fibres, which has resulted in an exceptionally stiff carbon-fibre reinforced 3D printer filament. CarbonFil is twice as stiff as HDglass and yet it is even 10% more impact resistant, which is a remarkable feature for carbon-fibre reinforced filament.

 

Unique features

  • Reinforced with 20% ultra-lightweight and relatively long carbon fibre stringers

  • Extremely stiff

  • Two times as stiff as HDglass (or even more compared to other PETG-based filaments)

  • Great impact resistance

  • 10% more impact resistant than HDglass (or even more compared to other PETG-based filaments)

  • Very easy to print

  • Nearly warp-free, improved thermal stability, nearly perfect first layer and inter-layer adhesion

  • Good first layer adhesion to a heated glass print bed and many other surfaces

  • Heat deflection temperature of ± 85° C

  • Great dimensional stability

General printing guidelines *

Nozzle size: ≥ 0.5mmLayer height: ≥ 0.3mmFlow rate: ± 100%
Print temp: ± 230 - 265° CPrint speed: HighRetraction: Yes ± 6mm
Heat bed: ± 0 - 60° CFan speed: 50-100%Experience level: Beginner

*) Above displayed settings are meant as guidance to find your optimal print settings. These ranges in settings should work for most printers, but please do feel free to experiment outside these ranges if you think it is suitable for your printer. There are a lot of different type of printers, hot-ends and printer offsets that it is extremely difficult to give an overall one-size-fits-all setting.

Abrasiveness

Please be aware that CarbonFil filaments contain a relatively high concentration of extremely hard carbon fibres, which have an abrasive nature. In general these carbon fibres will accelerate the nozzle-wear of brass nozzles, much faster than unfilled filaments. We recommend to use nozzles from stainless steel or other hardened alloys. 

Filament length

ρ: 1.19 g/cc50 gr coil0.5 Kg spool2.3 Kg spool
Ø 1.75mm± 17.5m± 175m± 804m
Ø 2.85mm± 6.6m± 66m± 303m

Nozzle cleaning

When printing with filled/composite filaments it is recommended to clean your nozzle immediately after printing by feeding 15-20cm PLA filament through your nozzle. This will make sure that any potential fillers are flown out of your nozzle. It is even better to use glow in the dark PLA as the extremely hard phosphorous particles are much more likely to scrape out residual waste from your nozzle.

Product export information

HS Code: 39169090Description: MonofilamentCountry of origin: the Netherlands

Compliance *

This filament is compliant to below listed directives and regulations.

  • RoHS directive 2011/65/EC

  • REACH directive 1907/2006/EC

*) This declaration of conformity to directives and regulations is pre

Filamentstørrelse 1,75mm
Informasjon Inneholder partikler som sliter på messingdyser. Ståldyse anbefales!
Vanskelighetsgrad Middels
Tittel Type Størrelse Last ned
MSDS---CarbonFil.pdf PDF 220.83KB Last ned
CarbonFil---TDS---Formfutura.pdf PDF 108.66KB Last ned

Kommentarer 0


Produktets tagger

Det er ikke registrert noen tagger.

Mine tagger

Andre kunder har også kjøpt