1,75mm StoneFil Terracotta

1,75mm StoneFil Terracotta

329,00 NOK

(inkl. mva.)

Ingen produktomtale


PLA + 50% knust stein




± 0.05 mm

Oppvarmet byggeplate  

Nei, men 40-60ºC anbefales

Print temperatur

200 - 240°C

Filament vekt


Filament lengde

122 m  +/- 1%


200mm x 55mm

Spole hull diameter

53 mm

Vekt tom spole


Minst 0,4mm.

Inneholder partikler. 

Ståldyse anbefalt.

Modell/varenr.: 131-0-SFTC
Lagerstatus: På Lager
StoneFil is a PLA-based filament which is based on our modified and easy-to-print EasyFil PLA compound and is gravimetrically filled with 50% of powdered stone. 
This high “stone filling” has resulted in a 3D printer filament with remarkable aesthetic features and a significant higher material density up to 37% higher than “normal” PLA. StoneFil is an easy-to-print 3D printer filament and printed objects have an extremely matte stone-like finish with unique natural gradient colour linings resulting in an exceptional chromatic spectrum per print. Every StoneFil printed object will have its own identity and unique gradient colour shading.


Unique features

  • Easy to print

  • 50% gravimetric powdered stone filling

  • ±37% heavier than “normal” PLA

  • Matte and rough stone-like finish

  • Unique natural/organic gradient colour linings

  • Every print has its unique natural stone gradient colour shading

General printing guidelines *

Nozzle size: ≥ 0.4mm Layer height: ≥ 0.12mm Flow rate: ± 110%
Print temp: ± 200 - 240° C Print speed: High / Medium Retraction: Yes ± 5mm
Heat bed: ± 0 - 60° C Fan speed: 50-100% Experience level: Beginner

*) Above displayed settings are meant as guidance to find your optimal print settings. These ranges in settings should work for most printers, but please do feel free to experiment outside these ranges if you think it is suitable for your printer. There are a lot of different type of printers, hot-ends and printer offsets that it is extremely difficult to give an overall one-size-fits-all setting.


StoneFil has a very high filling with stone powders and therefore the filament can have a slightly more abrasive effect on brass nozzles than unfilled filaments.

Filament length

ρ: 1.70 g/cc 50 gr coil 0.5 Kg spool
Ø 1.75mm ± 12.2m ± 122m
Ø 2.85mm ± 4.6m ± 46m

Nozzle cleaning

When printing with filled/composite filaments it is recommended to clean your nozzle immediately after printing by feeding 15-20cm PLA filament through your nozzle. This will make sure that any potential fillers are flown out of your nozzle. It is even better to use glow in the dark PLA as the extremely hard phosphorous particles are much more likely to scrape out residual waste from your nozzle.

Product export information

HS Code: 39169090 Description: Monofilament Country of origin: the Netherlands

Compliance *

This filament is compliant to below listed directives and regulations.

  • RoHS directive 2011/65/EC

  • REACH directive 1907/2006/EC

*) This declaration of conformity to directives and regulations is prepared according to our present standard of knowledge and may be amended if new cognitions are available and applies only for the above described products.


Filamentstørrelse 1,75mm
Informasjon Inneholder partikler som sliter på messingdyser. Ståldyse anbefales!
Vanskelighetsgrad Enkel
Tittel Type Størrelse Last ned
MSDS---StoneFil---English.pdf PDF 680.59KB Last ned
StoneFil---TDS---Formfutura.pdf PDF 109.12KB Last ned

Kommentarer 0

Produktets tagger

Det er ikke registrert noen tagger.

Mine tagger

Andre kunder har også kjøpt